![]() ![]() The battery supplies power to these keypads in case of AC power loss. Use a UL Listed, battery-backed supply for UL installations. MOUNTING SCREWS INSTALLED 1/8” ABOVE SURFACEīacklight OFF, Sound OFF Backlight ON, Sound OFF Backlight ON, Sound ON 12V, 140mA 12V, 205mA 12V, 270mA 93% RH, no condensation 14˚ F to 131˚ F / -10˚ C to 55˚ C -40˚ F to 158˚ F / -40˚C to 70˚C Width: 8 inches (203.2mm) Height: 5-1/2 inches (139.7mm) Depth:1-3/8 inches (35mm)ĬONTROL TERMINAL STRIP POWER FROM SUPPLEMENTARY POWER SUPPLY IF USED SUPPLEMENTARY +12 VDC POWER SUPPLY P/N AD12612 CONTROL TERMINAL STRIP AUX AUX DATA DATA IN OUT Mount TouchCenter by sliding onto the screw heads.ĭETACH CASE FRONT BY REMOVING SCREWS (2) AND LIFT UP **Go to “Wiring the TouchCenter” and complete wiring 6. Locate the case back over the mounting surface such that the opening is aligned with the wire/cable access opening on the mounting surface while passing the wires/cable through the opening in the case back. Install 4 screws (supplied) in the mounting surface leaving screw heads 1/8” above the mounting surface. Use the template (provided in the carton) to mark the location of the mounting screws and the cut-out for the TouchCenter assembly on the mounting location. Detach the mounting plate by sliding downward and discard. Replace the case front and secure using the two bottom screws.ġ. Mount the TouchCenter in its final location, (see “Standard Mounting” or “Mounting without the mounting plate”) install center securing screw (supplied) and tighten to mounting surface. Gently pull up using a screwdriver if necessary and pry apart. Detach case front by removing the two bottom screws. Mounting (European Installations) using a center securing screw:ġ. The 6280 complies with the European Standard EN50131 and is designed to prevent unauthorized use. Secure the mounting plate to mounting surface using 4 screws (supplied). ***Go to “Wiring the TouchCenter” and complete wiring*** 5. Locate the mounting plate over the mounting surface such that the wire/cable access openings are aligned while passing the wires/cable through the case back. ![]() Use the mounting plate to mark the location of the mounting holes on the mounting surface and check for level. Detach the mounting plate by sliding downward. Standard Mounting with mounting plate: Mounting without mounting plate:ġ. Use the center securing screw for European installation. The TouchCenter can be mounted with or without the mounting plate. Avoid mounting in areas of high condensation such as bathrooms or in locations where bright light or sunlight shines directly on the screen. This Keypad is for indoor use only and should be mounted at a comfortable viewing level. MESSAGE (YELLOW) LED FLASHING – The system contains new message(s) for the User. ![]() If disarmed, faults or troubles are present. OFF – System is armed or disarmed but not ready. READY (GREEN) LED ON – System is disarmed and ready to arm. You must use the vocabulary list in your alarm panel instructions for actual words that may be annunciated refer to the Word List in this document.ĪRMED (RED) LED ON – System is armed. Word List The 6280 TouchCenter can annunciate a series of words. Wiring IMPORTANT: If you power the TouchCenter from your panel’s auxiliary power output, check your panel’s Installation and Setup Guide and verify that this device and others do not exceed your panel’s auxiliary power output capability if it does, a supplementary power supply is needed. Compatibility: For a list of alarm systems that the TouchCenter can interface with, refer to the Compatibility Table in this document. The 6280 Series graphical touch-screen keypads are Advanced User Interface (AUI) devices, which combine control of your security system, multi-media and premises lighting. This guide provides information on installing and setting up Honeywell's 6280 TouchCenter Keypads. 6280 TouchCenter Keypads Installation Guide ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |